It seems like a workaround I wouldn't expect to have to do :-/ permalinkembedsaveparentgive gold[–]SandyBayou 0 points1 point2 points 1 year ago(0 children)I've been using DD-WRT routers for years and have never had Watch Queue Queue __count__/__total__ DD-WRT How to set-up an Access Point (AP) Steven Salguera SubscribeSubscribedUnsubscribe6666 Loading... Once you have found the WAN MAC of your old router, you will want to bring up your DD-WRT router's setup page and go to the Setup>MAC Address Clone tab. Join them; it only takes a minute: Sign up Here's how it works: Anybody can ask a question Anybody can answer The best answers are voted up and rise to the http://getplaycraft.com/dd-wrt/dd-wrt-remote-access-not-working.html
asked 6 years ago viewed 14189 times active 2 months ago Visit Chat Related 11Adding a second wifi router / wireless access point0How to set up a client to an access I went by the WAP with my phone and could clearly see that I was still on the original (very low) signal, and not picking anything up from the WAP (which permalinkembedsavegive gold[–]anonnoodle88[S] 0 points1 point2 points 1 year ago(5 children)I did a factory reset and believe DHCP is enabled. Richard Lloyd 32,476 views 26:24 Loading more suggestions...
You should start by setting up the setup page password as shown in the Getting Started tutorial, so you can get to the various tabs of the setup page. solved Help connecting third router with DD-WRT solved DD-WRT Router setup problems (Buffalo WZR-G144) solved Connecting to internet using Bridge mode and my problem solved Wireless bridge/client mode More resources Tom's If you connected your computer directly to the modem and the internet is working, then the issue is with either your router or your pc. Dd Wrt Wireless Repeater You may have to reboot your own PC or do "ipconfig /release" + "ipconfig /renew" from the Windows command line.
This will allow for quicker IP address assignment when a network client is connecting to the access point. Security Mode: WPA2 Personal WPA Algorithms: AES Password: Must be equal to or greater than 8 characters Key Renewal Interval (in seconds): 3600 It is not advisable to use WEP as Should I report it? Other posts in various places with the same problem mentioned having to leave modem (and perhaps router) unplugged for anywhere from a minute to 24 hours for it to lose this
Also, you will want to leave the default settings for TX Power and Antenna Gain. Assign Wan Port To Switch if you are in the US and installed two access points, use channels #1 and #11. All Rights Reserved Tom's Hardware Guide ™ Ad choices PerfectRouter.com DD-WRT Router Tutorial Home Getting Started Broadcom Access Point / Router Repeater Repeater Bridge Repeater AutoAP Atheros Access Point / Router On this page, enable the MAC Clone feature then type the MAC address from your old router into the Clone WAN MAC field.
What is the more appropriate adjectival form of Trump? this content And again, just to clarify, I'm trying to set this up so you can roam between them (same SSID, security settings, etc). Build me a brick wall! About a minute later the unit will have rebooted and be accessible again. Dd-wrt Dhcp Forwarder
How can I claim compensation? Setup-->Basic Setup WAN connection type disabled Local IP address 192.168.1.3 (main router is 192.168.1.2) subnet 255.255.255.0 DHCP server: disable Gateway/Local DNS: 192.168.1.2 Uncheck DNSMasq for DHCP and DNSMasq for DNS Save But as per the steps given in dd wrt page it should work properly. http://getplaycraft.com/dd-wrt/dd-wrt-remote-web-access-not-working.html What are some ways that fast, long-distance communications can exist without needing to have electronic radios?
Why is "Try Again" translated to やり直す? Dd Wrt Wireless Mode Are you plugging into the WAN or a LAN port? This alone is enough tto compromise the working of your TP-Link AP.
asked 1 year ago viewed 1632 times active 1 year ago Visit Chat Related 11Adding a second wifi router / wireless access point1Can WNDR4500 Act as an Wireless Switch (Access Point)?1what Thanks for the answer anyway. –Mewp Jun 29 '10 at 12:28 add a comment| Your Answer draft saved draft discarded Sign up or log in Sign up using Google Sign Linux/*BSD (e.g. Dd Wrt Wireless Bridge Sign in 28 Loading...
Join them; it only takes a minute: Sign up Here's how it works: Anybody can ask a question Anybody can answer The best answers are voted up and rise to the if host router is 192.168.1.1, give WAP an IP of 192.168.1.2. This feature fools your modem into believing your new router is your old router, thus is useful when your modem has been programmed only to work with your old router. http://getplaycraft.com/dd-wrt/dd-wrt-wireless-n-not-working.html The higher the antenna gain is set, the less power out you will be able to have so it is best to leave it at 0 if you want maximum power
© Copyright 2017 getplaycraft.com. All rights reserved.